With a wiresheet open, disconnecting first unsubscribed its components and
waited for the reply, which a restarting device never sends, so the editor
froze until the request timed out. After restart, reboot, quit or hibernate
the session is now closed without asking the device anything; a plain
Disconnect still unsubscribes first.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The save and file-open requests used their own fixed resend intervals
(5 s / 15 s) and the hello asked for 256-byte packets. Ontrol's Sedona
Java stack does neither and works with the P-ION: the standard backoff
(1, 2, 4, 8 s) sends a busy device a few copies with the same seqNum,
which its receive window drops. Both are removed.
Also fixes a race in SendWindow.send(): the packet entered the window
before its payload and sent_time were set, so housekeeping could resend
it with an empty payload, and the device would then drop the real one
as a duplicate.
Tested on a P-ION at 192.168.1.252, App > Get with File: save 3.2 s
(2 resends), app.sab + kits.scode in 11.3 s with 500-byte chunks
(was 14.6 s at 256), device stayed up, files identical to a 256-byte
backup.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A real P-ION (fw 1.32) restarted on every Sox file get. Ontrol's Niagara 4
driver gets app.sab from the same device, so its settings are copied:
- DASP hello asks for 256-byte packets (idealMax/absMax), so file chunks
are 238 bytes
- the message-length header (0x81) goes to Orion only, decided once the
platform id is read
- the app is saved on the device before app.sab is read, the save resent
every 5 s rather than 1 s (a P-ION save takes 2-3+ s)
- the file open is resent every 15 s; DASP gains a per-packet resend
interval for this
Tested on a P-ION at 192.168.1.252: save 3.2 s, app.sab + kits.scode +
app.sax in 15.8 s, no resends, device stayed up. The unsaved-changes
question became a notice, since the app is now always saved first.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The schema built from a Sox session spelled checksums as signed decimals,
so no kit matched a manifest: Installed showed raw checksums and Action
read "Keep at checksum ...". They are now 8 hex digits like a .sax file,
and checksums compare regardless of zero-padding.
A device session only loads folders as they are opened, so only sys
counted as used. Used kits now come from the whole component tree, read
one request at a time so a small controller is not flooded into dropping
the session.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The root tree row now names the app component, "app (<host:port>)" or
"app (<file>)", and offers Properties from its context menu and on
double-click. The live DOM's <app> element now carries its type and slot
values, and the refresh-by-id lookup finds it, so the view shows real
sys::App values.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The device builds the schema and version replies in a fixed 512-byte
packet and drops whatever does not fit. Read strings defensively, recover
a cut-off checksum from the one local manifest matching its prefix, and
fail with a clear message when the kit list cannot be recovered.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The font and image rows are now dropdowns filled from <sedona home>/ontrol:
fontBank/imageBank on Rion, fontBankXL/imageBankXL on Orion. Orion lists
.oxfl fonts in landscape and .oxfp fonts in portrait, read from the
platform service's screenOrientation (loaded from the device in live mode
when the tree has not reached it). Images show their file extension while
the slot keeps the bare name. The font dialog is gone.
In portrait the Page Editor draws a 480x800 screen in
frame_orion_portrait.png, and the canvas renders text with the .oxfp
fonts, whose glyphs are stored a quarter turn anticlockwise.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Types with intermediate parents (e.g. ontrolOx::PushButtonImage ->
Widget -> Service -> Component) only got Component + own slots, so
config/runtime streams were decoded against the wrong slot list and
x/y/imageFileName came out wrong.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Populate prop elements with manifest default values when adding
components in both offline and live mode
- Send config values from manifest in SOX add command for live devices
- Refresh button in properties panel now fetches fresh values from
the connected device before re-reading the DOM
- Properties panel fetches device values on open in live mode
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Fix add component from palette in live mode: resolve <app> element
as comp_id 0, fix type_id lookup to use type_name_map, set type_name
on newly added SoxComponent, sync device values into DOM after add,
write meta position back to device, and subscribe new component to COV.
Fix delete component in live mode: clean up subscriptions for deleted
component and all its descendants.
Add tree root context menu with device app actions (save, hibernate,
quit, restart, reboot) in live mode. Device save clears dirty state.
Clean up connection lost handling to do a full disconnect.
Fix slot registry to copy base slots and renumber IDs correctly.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
_slot_name_by_id() now resolves SOX link slot IDs against the
inheritance-flattened final_components_registry instead of the
per-type slot_registry whose local IDs were wrong for types with
intermediate parents (e.g. RegFloat→Register→Component). This
produced incorrect link endpoints, inflated linked-slot visibility,
and different box sizes between file and live modes.
Also: tighten routing constants for denser wiring, add wiresheet
PNG print/export (Ctrl+P), sort link routing jobs by gap distance,
remove debug route logging, and fix live tree-expand re-selection.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Slots with no flags (sensor, controlSignal, out_*) were not skipped
during config property reads, consuming bytes that the device never
sent and misaligning every subsequent config value (setpoint,
proportionalBand, etc.) into tiny denormalized floats like 2.36875e-41.
Changed the filter in _apply_props from "skip if runtime" to "skip if
not config" so only explicitly config-flagged slots are read from config
messages. Also switched iter("slot") to findall("slot") in the slot
registry builder to avoid picking up nested descendants.
Float display now defaults to 2 decimal places everywhere (wiresheet
and properties panel), honouring the precision facet when one exists.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Adds _fmt_float() helper that formats 32-bit floats with :.6g precision
but appends .0 when the result has no decimal point, matching Niagara
and .sax file display conventions (e.g. 175.0 not 175, 0.0 not 0).
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Sox reads 32-bit floats that Python promotes to 64-bit doubles, producing
display artifacts like 22.011558532714844. Using :.6g format gives clean
values matching .sax file precision (22.0116, -19.9574, 175, 14).
Applied to both initial DOM build and COV update paths.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
- Build root children directly under <app> instead of wrapping them in
a <comp name="app"> element. This matches the .sax DOM structure
where <app> is the container, so component paths like /AHU/TmpCont/X
match between link references and get_component_path.
- Fix _comp_path to produce /AHU/TmpCont/X format (skip root id 0,
leading /) matching the .sax link path convention.
- Format float property values to 4 decimal places instead of full
Python float precision (22.0116 vs 22.011558532714844).
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
- Add type_name_map on SoxClient so components loaded after connect
resolve proper names (e.g. control::And2) instead of kit::typeN.
This lets the slot registry and final_components_registry match,
so component boxes show their slots and property values.
- Load live schema gracefully: skip missing kit manifests instead of
aborting, compile the kits we have, and warn about missing ones in
the status bar.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Three fixes so live wiresheets render identically to offline .sax files:
1. Inherit sys::Component base slots (meta) into every type's slot
registry so component x/y positions are read from the device.
2. Place <link> elements under a <links> container element instead of
directly under <app>, matching the .sax structure that draw_links
and build_linked_slot_index expect.
3. Deduplicate links (each link appears on both endpoints in Sox) so
wires are not drawn twice.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
On connect, also loads root's immediate children so the first tree level
shows real names. For deeper levels, inserts placeholder <comp> elements
for uncached children so the Treeview shows + expand arrows for folders
that have children on the device.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Port the DASP transport and Sox protocol stack from sedonaOntrol Java
to Python, enabling live device editing alongside the existing offline
SAX editor. Lazy-loads components on navigation, caches them, and
subscribes to COV events for the active wiresheet.
New files: dasp.py, sox.py, device_session.py, connect_dialog.py,
live_hooks.py. Modified: app_state.py (live-mode state), main.py
(Device menu, COV polling, lazy tree expand), properties.py (Sox
write-through), sax_file.py (structural mutations route through
live_hooks), schema.py (find_manifest helper).
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
ArdaandClaude Opus 5.5